Anycubic

145 - 163 of 163

Anycubic Kobra 3 (combo) 3D Printer with ACE Pro System Reduced!

Anycubic Kobra 3 (combo) 3D Printer with ACE Pro System DKI00263

Description Anycubic Kobra 3 3D Printer with ACE Pro multi-filament system for multi colour printing.

Bring the most colorful 3D prints to life with the Anycubic Kobra 3 Combo. This 3D printer comes with an Anycubic Color Engine Pro, allowing you to 3D print with up to 4 colors or types of filament at the same time. The Anycubic Color Engine Pro will automatically switch between colors or spools, allowing you to also use two spools of the same color as a backup for each other.

Intelligent
The smart algorithm helps the Anycubic Color Engine Pro load the right filament within a minute. To prevent the filament from becoming tangled, it is guided through 4 different tubes to the extruder. There is also a constant check to see whether the filament has run out. If this is the case, the screen will provide a real-time reminder, so there is less chance of your print failing. In addition, the algorithm measures the pressure in the nozzle for smooth extrusion, layer by layer. With just the push of a button you can use the vibration compensation. This will make your prints much smoother. The Kobra 3 Combo can also easily resume printing after a power failure or running out of filament.

User friendly
This 3D printer is very easy to set up and is suitable for both beginners and advanced users. Use the automatic bed leveling to always have a perfectly level print bed. You can easily operate the printer with the touchscreen, which you can also rotate 30˚ to 60˚ for extra comfort. The nozzle goes up to 300˚ C, making it suitable for many different types of filaments. In addition, it can be replaced easily and without tools. The 32 bit MCU has a silence sensor to reduce noise to a maximum of 50 dB. This means you will not be bothered by noise pollution during printing.

Other functionalities
The Kobra 3 has a sturdy frame that is suitable for long-term stable printing, even at high speeds. The stylish design ensures that this printer fits well in almost any interior. With a construction volume of no less than 250 x 250 x 260 mm and a maximum printing speed of 600 mm/s, you can easily make 3D prints of different sizes. The cooling fan spins up to 7,000 rpm, so your 3D models are cooled quickly. The filament can be dried during 3D printing, so it is always in optimal condition for printing. In addition, the filament is also kept dry when you are not printing. Finally, you can easily control your 3D printer via the Anycubic app ( Android & iOS )

Specifications

Dimensions:	505 x 453 x 483 mm	Printer has USB:	yes
Power rating:	400 W	Max print depth:	25 cm
Input voltage:	100-240V	Max print width:	25 cm
Filament diameter:	1.75 mm	Max print height:	26 cm
Nozzle diameter:	0.4 mm	Printer bed levelling:	automatic
Printer no of extruders:	1	Heatbed max temp:	100 °C
Brand:	Anycubic	Filament sensor:	yes
Weight:	13.8 kg	Printer extruder:	Direct
Network:	WiFi	Max print volume:	16.25
Heated bed included:	yes	Our item no:	DKI00263
Camera included:	no	Printer extruder max temp:	300 °C
Printing technique:	TFDM FFF	Printer voltage:	24 v/°c
Hazard class:	n/a

Recommended

123-3D Filament PLA Starterpack Black, White, Red, Grey and Blue 1.75mm 1kg

£70.00

123-3D Filament PLA Glitter Bundle 1.75mm 4 Pack

£72.00

123-3D Filament PLA Starterpack Black, White, Red, Yellow and Dark Blue 1.75mm 1kg

£70.00

*Filament not included

Was: £290
Now: £265.90

£265.90 (sold out)

£221.58 Excl. 20% VAT

Anycubic Photon Mono M7 Pro 3D Printer

Zoom in

Description

The Photon Mono M7 Pro flaunts remarkable printing speeds, clocking in at up to 130mm/h for standard resins and an astonishing 170mm/h with high-speed resin, all while preserving a precise layer height of 0.1mm. This performance is driven by its advanced 10.1-inch, 14K high-precision optical system, guaranteeing outstanding detail in each print.

Key Features

223 x 126 x 230mm Printing Volume
130mm/h for Even Standard Resins. 170mm/h with High-speed Resin, 0.1mm Layer
10.1, 14K (13320 5120) High-Precision Optical System
Auto-Adaptive Technology Control Heating
Auto Resin Refill, Withdrawal
Intelligent Workflow-Assist Printing

Specifications

Dimensions:	312 x 315 x 520 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	12.6 cm
Weight:	12.8 kg	Max print width:	22.3 cm
UV wavelength:	405 nm	Max print height:	23 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	6.46
Camera included:	no	Our item no:	DKI00266
Printing technique:	SLA DLP	Printer voltage:	24 v/°c

Order now, we can ship this tomorrow!

£425.00

£354.17 Excl. 20% VAT

In stock

Anycubic Photon Mono 4 Ultra 3D printer

Zoom in

Description The Anycubic Photon Mono 4 Ultra has a 7 inch 10K display with a pixel size of 17 x 17 µm and a resolution of 9024 x 5120. This allows you to easily bring your creative ideas to life and capture every detail. The 4.3 inch HD touchscreen has a completely new user interface design for an extra user-friendly and comfortable design.

Smart system
The smart support system helps you create perfect 3D prints and saves you up to 40% of the original printing time. In addition, the Photon Mono Ultra detects whether there is resin left behind so that you can clean it and the screen does not get damaged. The printer also keeps track of how much resin is left and gives a notification when it is too little. Printing is automatically stopped when a 3D print fails and you will receive a notification for other printing problems, such as cracks and detachment from the print bed.

Other functionalities
The Anycubic Photon is equipped with a new generation of ACF film, which has a positive effect on print time and release height. When this film has printed almost 30,000 layers, you will receive a notification to replace the film. This way you are always assured of the best quality. The advanced COB light source and Fresnel Lens provide precise 3˚ purple light, with which you can achieve an accuracy of approximately 0.01 - 0.05 mm. In combination with high speed resin, a speed of 120 mm can even be achieved. Use the Anycubic app ( iOS & Android ) to easily send print jobs via the cloud.

Please note : LCD screens have a limited warranty. If you have any problems, check the warranty period.

Specifications

Dimensions:	236 x 231 x 430 mm	Manual:	Download
Power rating:	72 W	Hazard class:	n/a
Input voltage:	110-220V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	15.34 cm
Weight:	5 kg	Max print width:	8.704 cm
UV wavelength:	405 nm	Max print height:	16.5 cm
Light source:	UV LED	Printer bed levelling:	manual
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	2.2
Camera included:	no	Our item no:	DKI00309
Printing technique:	SLA DLP	Printer voltage:	24 v/°c

£210.00 (sold out)

£175.00 Excl. 20% VAT

Anycubic Kobra 3 Max 3D printer

Zoom in

Description Unleash your creativity with the Anycubic Kobra 3 Max. This large 3D printer has a build volume of no less than 420 x 420 x 500 mm, making it easy to print even large 3D prints in one go. This allows you to easily create multiple models in the same batch, saving both time and filament and making it ideal for mass production. With a maximum speed of 600 mm/s and an acceleration of 10000 mm/s², you never have to wait long for your 3D prints to be ready.

User friendly
The LeviQ 3.0 automatic leveling system always ensures the perfect first layer. The belt tension is controlled semi-automatically, which prevents step loss and provides better stability when printing large multicolor 3D prints. Use the resonance compensation and active extrusion flow control to achieve even better results. In addition, the 'resume printing' function ensures that you can resume your 3D print after a power failure, so that it does not fail.

In just 125 seconds, the 800 W AC heated bed can be heated evenly to 60 ˚ C. The hotend can heat up to a temperature of 300 ˚ C, which means that you can print not only with filaments such as PLA and PETG, but also with materials such as TPU. You can easily change the nozzle thanks to the lever, so you can quickly continue with your next 3D printing project.

Other functionalities
This 3D printer has a spring steel build plate with PEI coating and a 4.3 inch touchscreen. You can use the Anycubic Slicer Next or another slicer. The Anycubic Next Slicer has various presets that make slicing even easier. In addition, it is compatible with file formats such as 3mf, stl, step, svg, obj, amf, ply and more. You can also use the Anycubic app, with which you can remotely monitor your print process.

Specifications

Dimensions:	706 x 640 x 753 mm	Hazard class:	n/a
Power rating:	300 W	Printer has USB:	yes
Input voltage:	100-240V	Max print depth:	42 cm
Filament diameter:	1.75 mm	Max print width:	42 cm
Nozzle diameter:	0.4 mm	Max print height:	50 cm
Printer no of extruders:	1	Printer bed levelling:	automatic
Brand:	Anycubic	Heatbed max temp:	90 °C
Weight:	19 kg	Filament sensor:	yes
Max print speed:	600 mm/s	Printer extruder:	Direct
Network:	WiFi	Max print volume:	88.2
Heated bed included:	yes	Our item no:	DKI00315
Camera included:	no	Printer extruder max temp:	300 °C
Printing technique:	TFDM FFF	Printer voltage:	24 v/°c

Order now, we can ship this tomorrow!

£369.00

£307.50 Excl. 20% VAT

In stock

Anycubic Kobra 3 Max Combo 3D printer

Zoom in

Description Unleash your creativity with the Anycubic Kobra 3 Max. This large 3D printer has a build volume of no less than 420 x 420 x 500 mm, making it easy to print even large 3D prints in one go. This allows you to easily create multiple models in the same batch, saving both time and filament and making it ideal for mass production. With a maximum speed of 600 mm/s and an acceleration of 10000 mm/s², you never have to wait long for your 3D prints to be ready. This combo also comes with an Ace Pro multi-material system.

Ace Pro
Thanks to the Ace Pro, you can 3D print with 4 colors or materials at the same time. By connecting an extra unit, this number can even be increased to 8. Changing spools will be fully automatic, allowing you to spend time on other things. The intelligent drying function of the Ace Pro makes it possible to dry filament, both before and during printing. This will make your 3D prints of even higher quality. In addition, the Ace Pro can automatically switch to a new spool of the same color when the old one is empty and the printing is paused when blockages or filament tangles are detected.

User friendly
The LeviQ 3.0 automatic leveling system always ensures the perfect first layer. The belt tension is controlled semi-automatically, which prevents step loss and provides better stability when printing large multicolor 3D prints. Use the resonance compensation and active extrusion flow control to achieve even better results. In addition, the 'resume printing' function ensures that you can resume your 3D print after a power failure, so that it does not fail.

In just 125 seconds, the 800 W AC heated bed can be heated evenly to 60 ˚ C. The hotend can heat up to a temperature of 300 ˚ C, which means that you can print not only with filaments such as PLA and PETG, but also with materials such as TPU. You can easily change the nozzle thanks to the lever, so you can quickly continue with your next 3D printing project.

Other functionalities
This 3D printer has a spring steel build plate with PEI coating and a 4.3 inch touchscreen. You can use the Anycubic Slicer Next or another slicer. The Anycubic Next Slicer has various presets that make slicing even easier. In addition, it is compatible with file formats such as 3mf, stl, step, svg, obj, amf, ply and more. You can also use the Anycubic app, with which you can remotely monitor your print process.

Specifications

Dimensions:	706 x 640 x 753 mm	Hazard class:	n/a
Power rating:	300 W	Printer has USB:	yes
Input voltage:	100-240V	Max print depth:	42 cm
Filament diameter:	1.75 mm	Max print width:	42 cm
Nozzle diameter:	0.4 mm	Max print height:	50 cm
Printer no of extruders:	1	Printer bed levelling:	automatic
Brand:	Anycubic	Heatbed max temp:	90 °C
Weight:	23.6 kg	Filament sensor:	yes
Max print speed:	600 mm/s	Printer extruder:	Direct
Network:	WiFi	Max print volume:	88.2
Heated bed included:	yes	Our item no:	DKI00316
Camera included:	no	Printer extruder max temp:	300 °C
Printing technique:	TFDM FFF	Printer voltage:	24 v/°c

Recommended

123-3D Filament PLA Starterpack Black, White, Red, Grey and Blue 1.75mm 1kg

£70.00

123-3D Filament PLA Glitter Bundle 1.75mm 4 Pack

£72.00

123-3D Filament PLA Starterpack Black, White, Red, Yellow and Dark Blue 1.75mm 1kg

£70.00

Order now, we can ship this tomorrow!

£499.00

£415.83 Excl. 20% VAT

In stock

Anycubic Photon Mono M7 Max 3D printer

Zoom in

Description Go for precision, volume and speed with the Photon Mono M7 Max 3D printer from Anycubic. Thanks to the build volume of this printer, you can easily print larger models such as masks or cosplay parts in one go. It is also possible to print multiple small models at the same time, increasing your productivity. With a maximum print speed of 63 mm/h, you can print considerably faster than with previous models.

High precision
The LighTurbo 3.0 high-precision light source uses a fresnel lens in combination with a COB light source. This ensures an accuracy of 46 µm and a model tolerance of ± 0.01 – 0.05 mm. This means that even the smallest details will be printed razor-sharp. The smart release system uses self-designed algorithms and mechanical sensors to dynamically adjust the lift height of each layer. This increases the chance of success with your 3D print.

User friendly
The Anycubic Photon Mono M7 Max has an automatic 3D printer inspection, which checks the internal parts of your 3D printer. Also, the residue detection will notify you when there are hardened pieces left in the resin vat, so you can clean them up and prevent your 3D print from failing. When your 3D printer is approaching 45,000 releases, the system will give you a notification, so you can replace your film in time. When the printer detects that a 3D print is not being printed properly, it will pause so you can fix the problem. After your printer is done, the model can be hung above the vat at an angle so that excess resin can drip off. Thanks to the user-friendly user interface, you can easily operate this 3D printer.

Automatic
The even heating automatically heats the resin to a temperature of 25 ˚ C, but it is also possible to preheat the resin manually to a temperature between 20 and 40 ˚ C. The 7K 6480 x 3600 px high resolution screen ensures sharp details and by using the anti-aliasing function an even smoother result can be achieved. Thanks to the automatic resin recycling, the resin levels are monitored with a sensor and refilled by the built-in air pump. This prevents your 3D print from being interrupted and reduces waste. You can also choose to manually refill the resin barrel when you receive a message that the resin level is too low.

Handy design
The easy flip-open design makes it possible to open the lid with even 1 hand. The leveling guide allows you to level your 3D printer on 4 points in an instant. The 1300ml resin tank is larger than previous models, making this 3D printer ideal for creating larger and industrial models. The air shaft can be connected to an external air purifier to reduce resin smell and improve air quality.

Specifications

Dimensions:	425 x 362 x 652 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	16.4 cm
Weight:	24 kg	Max print width:	29.8 cm
UV wavelength:	405 nm	Max print height:	30 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	14.661
Camera included:	no	Our item no:	DKI00317
Printing technique:	SLA DLP	Printer voltage:	24 v/°c
Manual:	Download

£648.00

£540.00 Excl. 20% VAT

14 day delivery

Anycubic Kobra 3 V2 (Combo) 3D printer

Zoom in

Description The Anycubic Kobra 3 V2 Combo combines lightning-fast 3D printing with impressive multi-color functionality. Thanks to the included ACE Pro module, you can print up to 8 colors in a single model. Advanced features like AI detection, filament drying, and an integrated camera make this printer a powerful and versatile all-rounder.

Key Features:

Building volume: 255 × 255 × 260 mm
Print speed: up to 600mm/s, recommended 300mm/s
Supported filaments: PLA, PETG, TPU, HIPS (Compatible with ABS, ASA, PA, PC, PP when used inside an enclosure)

Specifications

Dimensions:	505 x 453 x 483 mm	Hazard class:	n/a
Power rating:	400 W	Printer has USB:	yes
Input voltage:	100-240V	Max print depth:	25.5 cm
Filament diameter:	1.75 mm	Max print width:	25.5 cm
Nozzle diameter:	0.4 mm	Max print height:	26 cm
Printer no of extruders:	1	Printer bed levelling:	automatic
Brand:	Anycubic	Heatbed max temp:	110 °C
Weight:	14 kg	Filament sensor:	yes
Max print speed:	600 mm/s	Printer extruder:	Direct
Network:	WiFi	Max print volume:	16.9
Heated bed included:	yes	Our item no:	DKI00396
Camera included:	yes	Printer extruder max temp:	300 °C
Printing technique:	TFDM FFF	Printer voltage:	24 v/°c

Order now, we can ship this tomorrow!

£295.00

£245.83 Excl. 20% VAT

In stock

Anycubic Kobra X 3D Printer

Zoom in

Description The Anycubic Kobra X is a fast and accessible FDM 3D printer for makers who want to start multi-color printing immediately. This printer combines a generous build volume of 260 x 260 x 260 mm with a built-in 4-color system, high print speeds of up to 600 mm/s, and support for both standard and more technical filaments. This makes the Kobra X interesting for hobbyists, designers, and families who want to print colorful models, prototypes, and functional parts without much hassle.

Key features:

Construction volume: 260 x 260 x 260 mm
Print speed: recommended 300 mm/s, maximum 600 mm/s
Built-in 4-color system, expandable to 19 colors

Specifications

Dimensions:	455.4 x 445.3 x 461.3 mm	Printer has USB:	yes
Input voltage:	100-240V	Max print depth:	26 cm
Filament diameter:	1.75 mm	Max print width:	26 cm
Nozzle diameter:	0.4 mm	Max print height:	26 cm
Printer no of extruders:	1	Printer bed levelling:	automatic
Brand:	Anycubic	Heatbed max temp:	100 °C
Weight:	9.5 kg	Filament sensor:	yes
Max print speed:	600 mm/s	Printer extruder:	Direct
Network:	WiFi	Max print volume:	17.576
Heated bed included:	yes	Our item no:	DKI00544
Camera included:	yes	Printer extruder max temp:	300 °C
Printing technique:	TFDM FFF	Printer voltage:	24 v/°c
Hazard class:	n/a

£259.00

£215.83 Excl. 20% VAT

14 day delivery

Anycubic Photon Mono M7 Max + Wash & Cure 3 Plus

Zoom in

Description This Bundle contains the Anycubic Photon Mono M7 Max & Wash & Cure 3 Plus

Anycubic Photon Mono M7 Max:

Go for precision, volume and speed with the Photon Mono M7 Max 3D printer from Anycubic. Thanks to the build volume of this printer, you can easily print larger models such as masks or cosplay parts in one go. It is also possible to print multiple small models at the same time, increasing your productivity. With a maximum print speed of 63 mm/h, you can print considerably faster than with previous models.

High precision
The LighTurbo 3.0 high-precision light source uses a fresnel lens in combination with a COB light source. This ensures an accuracy of 46 µm and a model tolerance of ± 0.01 – 0.05 mm. This means that even the smallest details will be printed razor-sharp. The smart release system uses self-designed algorithms and mechanical sensors to dynamically adjust the lift height of each layer. This increases the chance of success with your 3D print.

User friendly
The Anycubic Photon Mono M7 Max has an automatic 3D printer inspection, which checks the internal parts of your 3D printer. Also, the residue detection will notify you when there are hardened pieces left in the resin vat, so you can clean them up and prevent your 3D print from failing. When your 3D printer is approaching 45,000 releases, the system will give you a notification, so you can replace your film in time. When the printer detects that a 3D print is not being printed properly, it will pause so you can fix the problem. After your printer is done, the model can be hung above the vat at an angle so that excess resin can drip off. Thanks to the user-friendly user interface, you can easily operate this 3D printer.

Automatic
The even heating automatically heats the resin to a temperature of 25 ˚ C, but it is also possible to preheat the resin manually to a temperature between 20 and 40 ˚ C. The 7K 6480 x 3600 px high resolution screen ensures sharp details and by using the anti-aliasing function an even smoother result can be achieved. Thanks to the automatic resin recycling, the resin levels are monitored with a sensor and refilled by the built-in air pump. This prevents your 3D print from being interrupted and reduces waste. You can also choose to manually refill the resin barrel when you receive a message that the resin level is too low.

Handy design
The easy flip-open design makes it possible to open the lid with even 1 hand. The leveling guide allows you to level your 3D printer on 4 points in an instant. The 1300ml resin tank is larger than previous models, making this 3D printer ideal for creating larger and industrial models. The air shaft can be connected to an external air purifier to reduce resin smell and improve air quality.

Anycubic Wash & Cure 3 Plus:

Speed up the post-processing of your 3D prints by using the Wash & Cure 3 Plus from Anycubic. This Wash & Cure machine has a larger capacity than previous Anycubic Wash & Cure machines. It has a large capacity of 7.6 liters and can wash and cure a 3D print of up to 228 x 128 x 260 mm. It is possible to clean the 3D print by placing it in the supplied basket or by hanging it from the top.

Higher quality
The design uses an innovative Flexicure light with a gooseneck, which increases the energy value by 30,000 W/cm². This results in improved curing in crucial areas, such as the top of your print and other hard-to-reach parts. The Wash & Cure 3 Plus uses a new setup, which cures 3D prints 20% more uniformly. This allows for more precise curing, resulting in greater consistency and higher quality.

Efficient & fast
The basket in which you can place your 3D model for cleaning is made of double-layer PP and supports washing parts with the build plate. In addition, you will never have problems with rust on the basket, because this material is rust-free. The basket comes with two heights at which you can adjust it: 150 mm and 250 mm. This allows the cleaning alcohol to be used more efficiently. The new two-layer curing platform also gives the option to cure a larger number of smaller 3D prints at once. This will speed up your 3D printing process significantly.

User friendly
Both washing and curing can be easily selected. The goose neck light can also be turned on or off with just one click. The washing and curing time can be set between 1 and 30 minutes. The design is designed to operate more quietly, creating a comfortable working environment.

Specifications

Dimensions:	425 x 362 x 652 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	16.4 cm
Weight:	24 kg	Max print width:	29.8 cm
UV wavelength:	405 nm	Max print height:	30 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	14.661
Camera included:	no	Our item no:	DKI00560
Printing technique:	SLA DLP	Printer voltage:	24 v/°c
Manual:	Download

£788.00 (sold out)

£656.67 Excl. 20% VAT

Anycubic Photon Mono M7 Max + Wash & Cure 3 Max

Zoom in

Description This Bundle contains the Anycubic Photon Mono M7 Max & Wash & Cure 3 Max

Anycubic Photon Mono M7 Max:

Go for precision, volume and speed with the Photon Mono M7 Max 3D printer from Anycubic. Thanks to the build volume of this printer, you can easily print larger models such as masks or cosplay parts in one go. It is also possible to print multiple small models at the same time, increasing your productivity. With a maximum print speed of 63 mm/h, you can print considerably faster than with previous models.

High precision
The LighTurbo 3.0 high-precision light source uses a fresnel lens in combination with a COB light source. This ensures an accuracy of 46 µm and a model tolerance of ± 0.01 – 0.05 mm. This means that even the smallest details will be printed razor-sharp. The smart release system uses self-designed algorithms and mechanical sensors to dynamically adjust the lift height of each layer. This increases the chance of success with your 3D print.

User friendly
The Anycubic Photon Mono M7 Max has an automatic 3D printer inspection, which checks the internal parts of your 3D printer. Also, the residue detection will notify you when there are hardened pieces left in the resin vat, so you can clean them up and prevent your 3D print from failing. When your 3D printer is approaching 45,000 releases, the system will give you a notification, so you can replace your film in time. When the printer detects that a 3D print is not being printed properly, it will pause so you can fix the problem. After your printer is done, the model can be hung above the vat at an angle so that excess resin can drip off. Thanks to the user-friendly user interface, you can easily operate this 3D printer.

Automatic
The even heating automatically heats the resin to a temperature of 25 ˚ C, but it is also possible to preheat the resin manually to a temperature between 20 and 40 ˚ C. The 7K 6480 x 3600 px high resolution screen ensures sharp details and by using the anti-aliasing function an even smoother result can be achieved. Thanks to the automatic resin recycling, the resin levels are monitored with a sensor and refilled by the built-in air pump. This prevents your 3D print from being interrupted and reduces waste. You can also choose to manually refill the resin barrel when you receive a message that the resin level is too low.

Handy design
The easy flip-open design makes it possible to open the lid with even 1 hand. The leveling guide allows you to level your 3D printer on 4 points in an instant. The 1300ml resin tank is larger than previous models, making this 3D printer ideal for creating larger and industrial models. The air shaft can be connected to an external air purifier to reduce resin smell and improve air quality.

Anycubic Wash & Cure 3 Max:

Simplify your finishing process with the complete Wash & Cure 3 Max from Anycubic. Washing and curing your model will be streamlined, so you no longer have to do this manually. The white design with grey lid is stylish and minimalist, so it fits in with any interior.

Big format
This machine has an impressive maximum cleaning capacity of 14.9 liters. The maximum size for 3D prints is 300 x 165 x 300. This leaves plenty of room for cleaning and curing one or more of your resin 3D prints. It is also possible to place a model complete with the building plate in this machine.

Efficient
The Wash & Cure Max cleans by using the 'spray cleaning' method. Your print will then be exposed 360° on a rotating platform, so that all sides of your model are evenly cured. The cleaning alcohol is used efficiently, resulting in savings of more than 50%. Due to the cleaning method, your print will still be thoroughly cleaned, without losing much alcohol. A 5 liter isopropyl bucket can clean up to 20 models.

Intelligent
The smart detection will identify problems and notify you. For example, this machine can register when you try to turn on the machine when the lid is open, no water is coming in or when the drain is not working properly and liquid remains in the bucket. This avoids any problems during post-processing.

Specifications

Dimensions:	425 x 362 x 652 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	16.4 cm
Weight:	24 kg	Max print width:	29.8 cm
UV wavelength:	405 nm	Max print height:	30 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	14.661
Camera included:	no	Our item no:	DKI00561
Printing technique:	SLA DLP	Printer voltage:	24 v/°c
Manual:	Download

£900.00 (sold out)

£750.00 Excl. 20% VAT

Anycubic Photon Mono M7 Pro + Wash & Cure 3 Plus

Zoom in

Description This Bundle Contains the Anycubic Photon Mono M7 Pro & Wash & Cure 3 Plus

Anycubic Photon Mono M7 Pro:

Key Features

223 x 126 x 230mm Printing Volume
130mm/h for Even Standard Resins. 170mm/h with High-speed Resin, 0.1mm Layer
10.1, 14K (13320 5120) High-Precision Optical System
Auto-Adaptive Technology Control Heating
Auto Resin Refill, Withdrawal
Intelligent Workflow-Assist Printing

Anycubic Wash & Cure 3 Plus:

Speed up the post-processing of your 3D prints by using the Wash & Cure 3 Plus from Anycubic. This Wash & Cure machine has a larger capacity than previous Anycubic Wash & Cure machines. It has a large capacity of 7.6 liters and can wash and cure a 3D print of up to 228 x 128 x 260 mm. It is possible to clean the 3D print by placing it in the supplied basket or by hanging it from the top.

Higher quality
The design uses an innovative Flexicure light with a gooseneck, which increases the energy value by 30,000 W/cm². This results in improved curing in crucial areas, such as the top of your print and other hard-to-reach parts. The Wash & Cure 3 Plus uses a new setup, which cures 3D prints 20% more uniformly. This allows for more precise curing, resulting in greater consistency and higher quality.

Efficient & fast
The basket in which you can place your 3D model for cleaning is made of double-layer PP and supports washing parts with the build plate. In addition, you will never have problems with rust on the basket, because this material is rust-free. The basket comes with two heights at which you can adjust it: 150 mm and 250 mm. This allows the cleaning alcohol to be used more efficiently. The new two-layer curing platform also gives the option to cure a larger number of smaller 3D prints at once. This will speed up your 3D printing process significantly.

User friendly
Both washing and curing can be easily selected. The goose neck light can also be turned on or off with just one click. The washing and curing time can be set between 1 and 30 minutes. The design is designed to operate more quietly, creating a comfortable working environment.

Specifications

Dimensions:	312 x 315 x 520 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	12.6 cm
Weight:	12.8 kg	Max print width:	22.3 cm
UV wavelength:	405 nm	Max print height:	23 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	6.46
Camera included:	no	Our item no:	DKI00562
Printing technique:	SLA DLP	Printer voltage:	24 v/°c

£590.00 (sold out)

£491.67 Excl. 20% VAT

Anycubic Photon Mono M7 Pro + Wash & Cure 3 Max

Zoom in

Description

This Bundle contains the Anycubic Photon Mono M7 Pro & Wash & Cure 3 Max

Anycubic Photon Mono M7 Pro:

The Photon Mono M7 Pro flaunts remarkable printing speeds, clocking in at up to 130mm/h for standard resins and an astonishing 170mm/h with high-speed resin, all while preserving a precise layer height of 0.1mm. This performance is driven by its advanced 10.1-inch, 14K high-precision optical system, guaranteeing outstanding detail in each print.

Key Features

223 x 126 x 230mm Printing Volume
130mm/h for Even Standard Resins. 170mm/h with High-speed Resin, 0.1mm Layer
10.1, 14K (13320 5120) High-Precision Optical System
Auto-Adaptive Technology Control Heating
Auto Resin Refill, Withdrawal
Intelligent Workflow-Assist Printing

Wash & Cure 3 Max:

Simplify your finishing process with the complete Wash & Cure 3 Max from Anycubic. Washing and curing your model will be streamlined, so you no longer have to do this manually. The white design with grey lid is stylish and minimalist, so it fits in with any interior.

Big format
This machine has an impressive maximum cleaning capacity of 14.9 liters. The maximum size for 3D prints is 300 x 165 x 300. This leaves plenty of room for cleaning and curing one or more of your resin 3D prints. It is also possible to place a model complete with the building plate in this machine.

Efficient
The Wash & Cure Max cleans by using the 'spray cleaning' method. Your print will then be exposed 360° on a rotating platform, so that all sides of your model are evenly cured. The cleaning alcohol is used efficiently, resulting in savings of more than 50%. Due to the cleaning method, your print will still be thoroughly cleaned, without losing much alcohol. A 5 liter isopropyl bucket can clean up to 20 models.

Intelligent
The smart detection will identify problems and notify you. For example, this machine can register when you try to turn on the machine when the lid is open, no water is coming in or when the drain is not working properly and liquid remains in the bucket. This avoids any problems during post-processing.

Specifications

Dimensions:	312 x 315 x 520 mm	Hazard class:	n/a
Input voltage:	110-240V	Printer has USB:	yes
Brand:	Anycubic	Max print depth:	12.6 cm
Weight:	12.8 kg	Max print width:	22.3 cm
UV wavelength:	405 nm	Max print height:	23 cm
Light source:	UV LED	Printer bed levelling:	automatic
Network:	WiFi	Filament sensor:	no
Heated bed included:	no	Max print volume:	6.46
Camera included:	no	Our item no:	DKI00563
Printing technique:	SLA DLP	Printer voltage:	24 v/°c

Order now, we can ship this tomorrow!

£720.00

£600.00 Excl. 20% VAT

In stock

Anycubic standard resin grey 1 kg

Zoom in

Description Quickly create high-quality 3D prints with Anycubic's standard resin. This resin produces strong 3D prints with minimal shrinkage. At the same time, the printing time is accelerated and the curing time is reduced, making 3D printing more efficient. The performance of this resin makes it an ideal choice for beginners. It has a good balance between stiffness, hardness, resilience and detail. The print remains firmly in place during printing, but is easy to remove after printing. You can easily store the resin in different environments without affecting the quality. This resin works between 365 and 410 nm UV wavelength, comes in the color grey and is in a 1 kg bottle.

Specifications

Colour:	Grey	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:		Resin tensile strength:	-
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06013

Colour:

Black

Grey

White

£18.85

£15.71 Excl. 20% VAT

14 day delivery

Anycubic standard resin black 1 kg

Zoom in

Description Quickly create high-quality 3D prints with Anycubic's standard resin. This resin produces strong 3D prints with minimal shrinkage. At the same time, the printing time is accelerated and the curing time is reduced, making 3D printing more efficient. The performance of this resin makes it an ideal choice for beginners. It has a good balance between stiffness, hardness, resilience and details. The print remains firmly in place during printing, but is easy to remove after printing. You can easily store the resin in different environments without affecting the quality. This resin works between 365 and 410 nm UV wavelength, comes in the color black and is in a 1 kg bottle.

Specifications

Colour:	Black	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:		Resin tensile strength:	-
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06014

Colour:

Black

Grey

White

£18.85 (sold out)

£15.71 Excl. 20% VAT

Anycubic standard resin white 1 kg

Zoom in

Description Quickly create high-quality 3D prints with Anycubic's standard resin. This resin produces strong 3D prints with minimal shrinkage. At the same time, the printing time is accelerated and the curing time is reduced, making 3D printing more efficient. The performance of this resin makes it an ideal choice for beginners. It has a good balance between stiffness, hardness, resilience and details. The print remains firmly in place during printing, but is easy to remove after printing. You can easily store the resin in different environments without affecting the quality. This resin works between 365 and 410 nm UV wavelength, comes in the color white and is in a 1 kg bottle.

Specifications

Colour:	White	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:		Resin tensile strength:	-
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06015

Colour:

Black

Grey

White

£18.85

£15.71 Excl. 20% VAT

14 day delivery

Anycubic water washable resin grey 1 kg

Zoom in

Description This water washable resin from Anycubic is very user-friendly. After 3D printing, you can simply wash it with water instead of alcohol. You can also easily use this resin in combination with a wash and cure machine. The resin has good fluidity and needs less time to be exposed to UV light, which makes your printing process faster. Thanks to the improved formula, 3D models made with this resin perform for a long time, without showing cracks. This resin works between the 365 and 405 nm UV wavelength, comes in the color white and is in a 1 kg bottle.

Specifications

Colour:	Grey	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:		Resin tensile strength:	-
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06016

£22.00 (sold out)

£18.33 Excl. 20% VAT

Anycubic ABS-like Pro 2 resin grey 1 kg

Zoom in

Description This ABS-like resin from Anycubic makes your 3D prints strong and durable. Minimal shrinkage, so your print does not deform. This allows you to achieve fantastic precision and sharp details. The low viscosity and high fluidity shorten the time the resin needs to harden. The resin also has good adhesion to the build plate, which reduces the chance of 3D prints failing. Anycubic ABS-like resin is made of a non-irritating composition that has little odor and is an eco-friendly choice. This resin works between the 365 and 405 nm UV wavelength, comes in the color grey and is in a 1 kg bottle.

Specifications

Colour:	Grey	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:		Resin tensile strength:	-
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06017

£24.70 (sold out)

£20.58 Excl. 20% VAT

Anycubic ABS-Like Resin V2 - Grey - 1 kg

Zoom in

Description Create strong and hard 3D prints with ABS-Like Resin V2 from Anycubic. This resin has high impact resistance, good durability and a mild odor. This means that 3D prints can withstand exposure to a natural environment for up to a year without showing any defects. 3D prints have high precision and minimal shrinkage, making models very detailed. In addition, it is easy to clean with water and can be easily post-processed. ABS-Like Resin V2 is extremely suitable for making tools and parts that require high performance.

Specifications

Colour:	Grey	Download SDS:	Download
Amount:	1 kg	Resin density:
Hardness:	80-85D	Resin tensile strength:
Brand:	Anycubic	Hazard class:	9
UV wavelength:	365-405 nm	Our item no:	DLQ06029